SOSA · The Founder Diaries · For Designers
A scenting point is five lines on a drawing.
Draw them before the joinery.
Designers write to me asking where to leave space for a diffuser, usually at the week when the joinery drawings have already gone to the workshop. The honest answer is that there is very little space to leave and almost nothing to build. What there is to decide is a socket, a little clear air, a sightline, the surface underneath, and whether a hand can still reach the bottle in two years.
No recess, no bracket, no cabinetry. A socket in the right place, air around the device, a protected surface and somebody able to open it. That is the whole specification.

One of the SOSA guides written for designers. The zoning upstream of this is in a room-by-room fragrance plan; the document it should end in is a fragrance specification and owner handover.
The answer in 30 seconds
Five annotations, and not one of them is hardware
- Power, named per zone. A suitable dry socket inside each zone you mean to scent, on the electrical drawing.
- Clear air around the device. The clearances the manufacturer states for the model, off curtains, upholstery and the back of a sofa.
- A sightline you have chosen. Decide on the drawing whether the device is seen or out of the eye's path. Both are fine; an accident is not.
- The surface underneath. Wipeable and non-porous, under the device and under the changeover.
- Refill and service access. A hand, a bottle and a cloth must reach it. Nothing sealed in.
- What you still need from the client. Floor plan with ceiling heights, electrical drawing, and the door habit.
Why this is a drawing decision and not a shopping decision
Everything that goes wrong with a diffuser in a finished interior goes wrong for one of five reasons, and all five are settled on paper months before anybody buys anything. There is no socket in the zone, so a cable crosses a floor that was designed not to have one. There is no clear air around the device, so the scent collects behind a curtain instead of travelling. Nobody decided whether the machine would be seen, so it lands on the one surface the eye finds first. The surface beneath it is an untreated stone the client loves, and the first refill leaves a mark. Or the device has been set into joinery that cannot be opened, so refilling becomes a small demolition. None of these is a product fault, and none of them costs anything to avoid at the drawing stage. All of them are expensive after handover, when the only remedies left are a visible cable, a visible machine, or a joiner.
Start with power, because it decides the rest. पवन Pawan plugs straight into a wall socket with no cable, adapter or battery, so the socket position is the device position and a socket in a suitable dry spot is the whole electrical requirement. वायु Vaayu comes with a power adapter, so it wants a socket within reach of that adapter and a lead route that does not cross a walkway. Neither device holds a battery: a zone with no power is a zone with no scent, however carefully drawn.
Then draw the air. A diffuser does not scent a room, it scents the quantity of air it can reach, so it wants to sit where air already moves: clear of a curtain, clear of the back of a sofa, clear of the inside of a cupboard, and not in the direct throw of a split unit that will carry everything to one wall. Treat the manufacturer's stated clearances as a dimension rather than a suggestion. For an open living and dining zone, take internal area multiplied by ceiling height; the sizing method has a guide of its own, and the figure you want is cubic metres of enclosed air, never the super area from a brochure.
Sightlines come next, and this is the part designers are best at and most often skip. Decide deliberately whether the device is part of the composition or out of the eye's path. On a hall console it can be seen and look intentional; in a bedroom it is usually better one surface below the line you look along as you enter. What you should not do is leave that to the day the client unpacks the box, because the surface free on that day is almost always the one you spent longest styling.
The surface underneath is a two-minute conversation that saves a finish. Fragrance oil is an oil, and an oil on untreated stone, a limewashed plinth or an unsealed veneer can leave a mark that does not come out. Specify something wipeable and non-porous, and remember that the changeover happens above that surface rather than at a sink. Where the client insists on a porous top, schedule a small tray. There is a guide to protecting finishes if you want the detail.
Access I would put in bold on the drawing if I could. The device must be reached by a hand holding a bottle and wiped by a hand holding a cloth, for as long as the client owns it; anything that makes that awkward quietly ends the routine.
The one thing I would ask you not to draw
Do not seal a device into joinery. I am asked for this often and in the gentlest terms — a slim niche behind a fluted panel, a cut-out in the back of a console, a shadow gap the machine can disappear into. It photographs beautifully and it is the most reliable way to make a working device useless. A waterless diffuser has a bottle that must be opened and replaced, a surface that must be wiped, and air that must be able to leave it; an enclosure the owner cannot open or reach without tools removes all three.
There is a second reason, less obvious from the drawing board. SOSA publishes placement, clearance and dry-location requirements per model, and no custom enclosure is covered by them. If you build one, the only honest position I can take is that you are outside the manufacturer's instructions and I cannot tell you what the device will do inside it.
If the client's wish is simply that the machine not be seen, the answer is placement rather than enclosure: a lower shelf, the return of an L-shaped console, the far end of a sideboard, a socket behind a chair instead of beside the entrance. And if there is no socket where the device ought to live, the answer is a socket, drawn now, by a qualified electrician — not an extension lead across a finished floor. Working around existing power points is a separate guide, for people who cannot add one.
| What each annotation has to say | |
|---|---|
| Power | A suitable dry socket in the zone. Pawan: socket only. Vaayu: socket within reach of the supplied adapter, lead off the walkway. |
| Clearance and air | The manufacturer's clearances as a drawn dimension, off curtains, upholstery and the throw of a split unit. |
| Sightline | Seen and composed, or one surface below the entry sightline. Chosen on the drawing. |
| Surface | Wipeable and non-porous, under the device and under the changeover; a tray on a porous top. |
| Access | Hand, bottle and cloth reach it with nothing dismantled. No sealed niche, no fixed panel. |
| Zone volume | Internal area × ceiling height, per zone, with the door habit noted. Not super area, not the terrace. |
| Maintenance note | The refill listed as compatible with the specified model, and who changes it. |
“If a hand holding a bottle cannot reach it, you have not designed a scenting point. You have designed an ornament.”
For your interior designer: the annotation set, in order
Hand this to whoever draws the electrical layout. It is five annotations and one schedule line per zone, and it should cost nothing if it is done before the joinery package is issued.
- Mark the zones by volume, not by room. Internal area × ceiling height per zone, double heights in section, and a note of the doors the household keeps shut.
- Put a suitable dry socket inside each zone. On the electrical drawing, by a qualified electrician, positioned for the model you intend to specify.
- Dimension the clear air. The manufacturer's clearances, off curtains, upholstery, cupboard interiors and the throw of an air-conditioning unit.
- Choose the sightline and name the surface. Seen and composed, or below the entry sightline, so it is not chosen for you on unpacking day.
- Specify the surface and its protection. Wipeable and non-porous under the device and the changeover, or a scheduled tray.
- Keep it openable, then close with maintenance. No sealed niche or tool-only access; then the device per zone, the compatible refill, the tested setting and who changes it.
वायु and पवन · what you are specifying
Two devices, two drawing requirements
वायु Vaayu: SOSA app over Bluetooth and onboard buttons · run windows on a timer, on chosen days · key-lock · power adapter included · published for up to 1,000 m³ of a suitable connected zone.
पवन Pawan: SOSA app and timer · plugs straight into the wall socket with no cable, adapter or battery · one room up to about 500 sq ft · silent.
Neither holds a battery, so every scenting point you draw needs mains power at the socket.
Current prices and oil sets are on each product page.
See वायु VaayuSee पवन PawanQuestions, answered
Where should an interior designer leave space and power for a diffuser?
Can the diffuser be built into joinery so it is not visible?
What do you need from me to specify the devices?
Does SOSA carry out the installation on site?
Should the specification include the fragrance oil?
Continue in the SOSA guides
If you would rather ask a person
Send us the plan and the electrical drawing
Mark the zones you want to scent, the ceiling heights and the sockets you already have. We will say which device suits each zone, where it should sit and what to annotate, and where a zone is better left alone.
Write to SOSA on WhatsApp